Podívejte se na můj stojan – „Node Zero“ je oblast v domě, kde se spojí všechny kabelové televize. Níže je výběr N0, které patří našim čtenářům. Můžete vidět fotografie a přečíst si popisy různých projektů, od několika snadných komponent ve skříni pod schody až po obrovské instalace s více stojany. Doufejme, že tato stránka vám ukáže, co lze udělat, a inspirovat vás k tomu, abyste si udělali vlastní. (Pokud byste chtěli přidat svůj uzel Zero do naší galerie, spojte se do kontaktu).
David Balharrie – můj uzel0 je ve dvou částech domu. Hlavní část je uzavřená skříňka na stojanu v mé garáži, ve které jsou umístěny mé servery. Druhá část (Node1) je umístěna v domě a je centrálním bodem pro opravu CAT5. Na mém webu je ještě více podrobností a mnohem více obrázků.
Paul Gale, Silicon Pixel – můj Node0 postavený ve dvojité skříni. S celou soupravou se však docela zahřeje. Přidal jsem ventilátor stropního extraktu (typ in-line toalety), který je ovládán X10 AD10. To znamená, že to mohu zapnout/vypnout podle potřeby. V současné době to mám zapnout v 08:30 a vypnout, když je alarm pohodlí vyzbrojen do nočního režimu (protože ventilátor je trochu hlučný). Dalším upgradem je přizpůsobit tišší ventilátor s větším proudem vzduchu, protože Node0 se v létě stále velmi zahřeje.
Quinten Uijldert – Začalo to s malou skříňkou, ale poté, co byla garáž rozdělena do dvou prostorů, jsem to vykopal a všechno přišrouboval ke stolu/zdi, také odpovídá na jednu z otázek, které se na chvíli vrátily na běh z garáže. Důl je funkční několik let a pokud udržujete rychlostní stupeň v chodu, kondenzace nebo studená (ve skutečnosti je bonus!) Není problém. Jedinou věcí, kterou musíte udělat, je, když se vypnete (a na chvíli odejdete), je přivést je dovnitř a nechat je znovu stát se teplotou místnosti, než je začnete (protože kondenzace se pak usadí).
NICK LOCKE – Můj uzel Zero se rozprostírá po dvou stěnách v garáži, takže žádná jediná fotografie to nemohla udělat spravedlnost. Tato fotografie ukazuje čarodějství CBUS. První dvě skříňky zahrnují jediný osm kanálových stmívačů a tři dvanácticeová relé. Dolní kabinet je nedávným doplňkem a po návrhu od kolegy z ukha pravidelných zahrnuje stykače, které ještě více chrání kanály CBU, které řídí vnější bezpečnostní a bezpečnostní světla. Kromě CBU mám také komfortní instalaci. Ještě více podrobností a mnohem více obrázků je na mém webu, přičemž mnohem více se přidává po celou dobu.
Nigel Giddings – Toto je můj první pokus o uzel 0. V současné době buduji dům v N. Kentu, takže jsem ho mohl integrovat do základního designu. Když jsem byl manažerem v několika telekomunikačních společnostech, viděl jsem docela málo datových center a zkopíroval jsem z nich mnoho nápadů. Flexibilita je pro mě velmi nezbytná, takže mám několik opraváren a také jsem použil trasy kabelové televize, ke kterým lze snadno přistupovat. Dalším požadavkem na design je, že zbytek domu by měl vypadat co nejméně „normální“, takže můj uzel 0 je jediným místem pro mě, abych se vyjádřil. Jakékoli dotazy nebo komentáře mi pošlete e-mail na adresu nigel@corbenic.co.uk
Rob Mouser – Node 0 je přizpůsobená postavená skříňka/stůl v mé kanceláři. Kromě LCD obrazovek, reproduktorů na stropní montáž a XanTech Ir Eyes nemáme žádné vybavení nikde jinde v domě, které je viditelné. Celá myšlenka byla taková, že se zavřenými dveřmi vypadalo to jako jakákoli jiná skříňka a byla do značné míry tichá, postavena z ½ palce vrstvy a MDF a byla nastříkána tak, aby odpovídala barvě zdi v kanceláři, kvůli hmotnosti zařízení v the racks the structure is tied to the ceiling and floor joists. To the left and best of the desk we have two full height rack enclosures including all PC and AV equipment and above the desk includes the wiring patch panels for data, voice, audio and video. below the desk are the C-Bus consumer units for the lighting. The best hand unit also houses the comfort alarm install although this is not visible from any of the pictures.
Rob – Calling it Node 0 is probably a bit grandiose but it is where many of my bits sit under the stairs! The space is just 44x44x54cm thus why it looks so cramped. on the left are the incoming BT lines (3), patch panel below and HomeVision below that. Back wall houses the 3×8 pabx with two switches in front sitting on the Vigor 2600+. finally on the left we have power, wireless AP and an MSS100 for Homevision. The main servers are in the garage and sky is distributed from the loft.
Mark Cox – In node zero we have termination for the 3 CAT5 sockets and coax from each room, and the typical router, switch, cable television modem. The bottom best houses a 1-wire hub currently monitoring six room temperatures and offering switching for the heating. the box on the best that looks like a doorbell actually is an wireless doorbell receiver hooked into the 1-wire network. The rest of node 0 stores all those old PC bits and pieces I’ll never need but just can’t throw away (like an ISA SCSI card).
Harry Hendriks – Node 0 is in the upper half of a closable, customized built cupboard in MDF on the first floor. It is fully functional in our newly build home because 2 years. on the left hand side are the incoming (mostly cat 5) cable televisions from our home (IR-sensors, phone connection, TW 523, Camera’s and other video connections, safety and security connections and control, smoke detection, anemometer, temperatures, etc.).
They interconnect in a flexible manner to the Node 0 equipment side: the Homevision controller, a laptop PC linked with the WiFi + ADSL home network, a Power distribution board + supply unit + battery, + an I/O board (with relays and allowable windforce detection: 5 Bft), an X10 integrity testmodule, a phone unit and TW523. On top of the controller is an IR + RF relay unit for remote control of the variuous automated functions in the house or vicinity. The laptop is used for the Homevision monitoring software, the always on line Internet weather information data exchange and also as a easy PC-scope for measurements through the PC soundcard.
Philip Rogers-Davis – This is my Node Zero, and it’s located in the loft. I have a number of devices located in a 19” rack. From top to bottom, the purchase is as follows:
Power strip (6 sockets)
Linksys 18 Port 10/100 Switch
48 way CAT5 patch Panel
Netgear ADSL Router
Mini Keyboard & Mouse
2xUHF Modulators (CCTV video camera 1 & 2)
Home safety and security Server (CCTV) for Geovision
In the rack is a room thermostat that is connected to two high speed (but noisy) case fans in the home safety and security Server. When it gets a hot up there, the fans kick in and create a high through flow of air through the case, and stop the server from overheating. Overall, it has been worth the effort, and keeps everything much tidier and less prone to ‘accidents’ when in the loft!
From the top, there is:
48-port RJ45 patch panel
Netgear 24 port 10/100 Ethernet Switch
Netgear DG632 ADSL Modem/Router
The gap next to the router has variously been filled with a PlayStation 2, wireless audio/video sender, and separate firewall
Sky + PVR/satellite receiver
Denon DVD-2910 DVD Player
Windows XP Media Centre edition PC/ media server – Denon AVR-2805 receiver
The grey vents conceal 10cm hi-flow fans each with built-in temperature controls. tucked away is a Keene electronics IR distribution system so that I can control it all remotely from the front room. plus an energy-saving socket that turns everything off automatically when the TV is turned off. There has been an X10 system in place for lighting but that is on the blink at the moment.
dunks517 – The rack is made up from a 20u cannibalised cabinet, placed into a void in the home office.
Onkyo TX-SR605
Sky HD
Xbox 360
Xbox 360 HDDVD Addon
40Gb PS3
Acer idea 500 HTPC
24 port patch panel
2Tb of storage including media library
Hidden behind the blanking plates are a 16 Port Netgear ethernet switch, Netgear ADSL moden & router, HDMI Cat5 Balun attached to sky HD, Labgear Loftbox – Coax distribution, Keene ir controller, X10 CM12u usb interface. I am considering extending the rack to 40U and adding sliding shelves, a fan/extractor and placing the printer in the rack.
Simon Smith – numerous years ago I discovered the Automated home site, and within it was this Node Zero gallery. The projects in that gallery inspired me to build my own. The opportunity came up when moving into my current home – an old semi-detached house needing a little work. There was a period of several weeks between owning the house and moving in that implied that I could go crazy with installing cable televisions without anything getting in the way.
Read the full story on Simons diy rack project here .
Sdílejte toto:
Facebook
Cvrlikání
Reddit
LinkedIn
Pinterest
E-mailem
Více
Whatsapp
Tisk
Skype
Tumblr
Telegram
Kapsa